They are making a few great pointers related to How to Install a Bathtub in general in this great article further down.
Setting up a bathtub isn't specifically brain surgery, but it does require strong plumbing, woodworking, and occasionally, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably challenging job. If the old bathtub is readily easily accessible, the task can move immediately; if you need to open up a wall to get rid of the old bathtub and also place the brand-new bath tub, the task is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will require an assistant to vacate the old tub as well as embeded in the new one. Ensure you have actually certified yourself for the task and fit trying it. As opposed to hiring a professional to take over a halfway-completed job, it is much better to think about utilizing one prior to you begin. Possibilities are you may need an expert plumber to make tube links.
This short article will aid you set up a new bathtub in your bathroom if you have actually already acquired a new tub and also don't need to transform the arrangement of your previous water supply pipes.
Your devices and also product list ought to consist of the following:
Planning for the Setup
Firstly, the sustaining structure provided with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to make certain that if the tap includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets unit to prevent pressure on the bath tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you use every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be suited its last position.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, after that the first thing you need to do is detach the water supply. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the limited accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a cloth all set for the remaining water that will originate from the pipes. As soon as the supply pipes have actually been gotten rid of, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from turning during this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Utilizing the two wood boards under its feet, position the tub in the called for position. The wood boards are handy in evenly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four small points.
The next goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and also readjusting the feet on the tub up until the level reads level.
To mount taps, fit the bottom of the outermost flexible tap adapter to the suitable supply pipe by making a compression join; then do the same for the other faucet.
Activate the water and also check all joints and also brand-new pipework for leakages and tighten them if essential. Fill up the bathtub as well as also examine the overflow outlet and the regular electrical outlet for leakages.
Finally, repair the bath paneling as explained in the manufacturer's user's manual. Tiling and securing around the bath tub needs to wait until the tub has actually been utilized at least when as this will resolve it into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, then you will need a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in place in between the faucet and the sink. Protect the tap in position with the producer supplied backnut. As soon as the tap is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical tap connectors. The former kind should be connected to the faucet ends initially, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture a rigid seal, causing the water to permeate the wall between the bathroom and also the tiling, leading to problems with dampness and also possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures as well as installations. They are offered in tubes and cartridges, as well as are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill the bath tub with water before sealing, to permit the motion experienced when the bathtub is in use. The sealer can fracture relatively early if you do not consider this activity prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily available on the marketplace. It is a good idea to fit the floor tiles making use of waterproof or waterproof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Hopefully you liked our topic about A Step-by-Step Guide to Installing a Bathtub. Thanks a ton for spending some time to browse our article post. Sharing is caring. Helping others is fun. Many thanks for taking the time to read it.
Reliable plumber? Dial now!